Speed test for IPTV and streaming
Measure in about half a minute how fast your connection downloads, how quickly it responds and how steady it stays — and see what that is enough for: SD, HD, Full HD or 4K.
Please note: This measures the connection between your device and the nearest Cloudflare location that serves this page — not your provider's line to an IPTV server. The result varies with Wi-Fi, time of day and other devices on your network.
Measure your connection
Close other downloads and streams first. The test downloads at most about 320 megabytes, far less on slow connections.
Ready. Press “Start test” to begin.
| Quality | Rating |
|---|---|
| SDGuideline 3 Mbit/s | – |
| HD 720pGuideline 5 Mbit/s | – |
| Full HD 1080pGuideline 8 Mbit/s | – |
| 4K / UHDGuideline 25 Mbit/s | – |
Rating with 25 % headroom: “Good fit” means the result is at least the guideline plus 25 %, “Tight” lies between the guideline and the guideline plus 25 %, “Not enough” below. The guidelines are rough rules of thumb; a provider may differ. For several simultaneous streams use the bandwidth calculator.
How the test measures
The download test fetches test files from this site over three parallel connections and counts how many bytes arrive per second. The first second of every run is not counted, because a connection needs time to ramp up before it reaches full speed. There are three runs; the result shown is the median, the middle value, so a single bad moment hardly distorts it.
For latency and jitter the test sends ten tiny requests one after another and times each answer. Latency is the time for one round trip; we show the smallest and the mean value. Jitter is the average difference between two consecutive answers — the smaller it is, the steadier the connection.
Why there is no upload test
An upload test has to send data to a server that accepts and processes it. This site is static: it has no writing server and is not meant to get one, because we collect nothing. An honest upload test without a server is not possible, and we do not want to sell you an estimate as a measurement.
For IPTV this is tolerable: while watching, the data flows almost entirely from the server to you. Upload matters for video calls or uploading files, not for watching.
How to measure properly
- Cable instead of Wi-Fi: Connect the measuring device to the router with a LAN cable. Wi-Fi varies with distance, walls and neighbouring networks and often shows less than the line can deliver.
- Pause other downloads: Updates, cloud backups, game downloads and running streams on other devices share the same line and push the value down.
- One tab, only this test: Close other tabs with video or heavy web apps. VPNs and browser extensions that filter traffic can lower the result; switch them off for comparison.
- Measure several times: Measure at least three times and at different times of day, especially in the evening when many households stream. What counts is the value you get at your usual viewing time.
- Consider the device: Older phones, streaming sticks and routers with weak hardware are bottlenecks themselves. If a laptop on a cable is fast and the stick on Wi-Fi is slow, the radio path is the cause, not the plan.
Typical causes of low results
- Wi-Fi problems: Distance to the router, thick walls, the crowded 2.4 GHz band. Moving closer, switching to 5 GHz or running a cable is usually the quickest fix.
- A busy line at home: Several devices download at once; the router divides the capacity.
- An old or weak router: Older devices sometimes cannot deliver the booked speed, especially over Wi-Fi.
- Time of day and load: In the evening, more users share the same network segments in many networks.
- Plan and line: A plan usually names a maximum “up to” speed; everyday values lie below it.
- VPN, proxy, security software: Extra detours and inspection cost speed.
What the numbers mean for IPTV
A good result is a necessary but not a sufficient condition. This test measures the path to the nearest Cloudflare location. Your IPTV provider, however, sends from its own servers, often in other countries and over other network paths. A fast connection here does not guarantee that the provider's stream arrives smoothly: overloaded servers, peering bottlenecks between networks or throttling can still cause buffering.
The reverse holds too: if even this test is weak, the cause is very likely at your home — in the Wi-Fi, the router or the plan. That is the good news, because there you can change something. If the numbers here are good and the stream still stutters, have a look at the guide fix IPTV buffering.
The rating in the table uses the guidelines SD 3, HD 5, Full HD 8 and 4K 25 Mbit/s per stream. These are rough rules of thumb, not promises: depending on codec, provider and content, a stream needs more or less. Plan some headroom so short dips are not immediately visible. For several streams or an exact calculation use the bandwidth calculator; beforehand you can check with the M3U validator whether your own playlist is formally fine.
Frequently asked questions
Why does the test show fewer Mbit/s than my plan promises?
Because plans usually state a maximum speed and the test measures the path to the nearest Cloudflare location. Wi-Fi, other devices on the network, the time of day and the router all push the value down. Measure by cable and several times to narrow down the cause.
Why is there no upload test?
An upload test needs a writing server that accepts data. This site is static and collects nothing, so we only measure download, latency and jitter. For watching IPTV the download is what matters.
How many Mbit/s do I need for 4K IPTV?
As a rough guideline, 25 Mbit/s per 4K stream, about 31 Mbit/s with 25 % headroom. That is a rule of thumb; codec, provider and content can differ. Several streams add up, which the bandwidth calculator works out.
What do latency and jitter mean?
Latency is the time a small request needs for the round trip. Jitter is the average variation between consecutive answers. Low values mean a fast, steady connection; high jitter can contribute to dropouts in live streams.
Does the test store anything about me?
No, nothing on a server and nothing with third parties. The result stays only in your browser's tab session (sessionStorage) so the bandwidth calculator can take it over; it disappears when you close the tab and is never sent.
More tools
Data and explanation as a table
| Category | Value or explanation |
|---|---|
| SD | 3 |
| HD | 5 |
| Full HD | 8 |
| 4K | 25 |
Sources and reproducible checks
Store ratings describe feedback from store users. The review texts we classify are a separate sample; their number is not the denominator of the rating. Neither dataset is our own device test.
- Store export generated
- Latest dated store observation in this export
- 2026-10-18
- Curated feature matrix source date
- 2026-07-23
These dates refer to different sources. A new export does not recheck the curated features. Older feature, price and availability statements need a fresh check in the official listing for your device and country.
Store screenshots are supplied by the app publishers, not captured in our own tests. Store presence alone does not establish support for every TV model, input format or playback setup. TELOS belongs to this website operator; its availability must also be checked for the exact platform.
Speed test: it measures browser downloads to this website, not your IPTV provider. For an illustrative 20 Mbit/s input, the shared estimate classifies one HD stream with reserve as sufficient and one UHD stream as below its 25 Mbit/s base estimate. This is not an actual speed measurement or a playback guarantee.
Check one variable at a time: validate a nonprivate playlist sample, measure on the actual playback device, then compare the official device and input requirements. Record device, app version, date and the result before changing another setting.